SR45A-AXHS and SR60A-AXHS end-of-shaft slip rings
Forty-five-circuit end-of-shaft slip ring with circular connectors on rotor and stator, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Sixty-circuit end-of-shaft slip ring with circular connectors on rotor and stator, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
- 45
- Circuits
- 4 000 rpm
- Max speed
- 250 mA
- Current per circuit
- 181.61 mm · 794 g
- Length · weight
- 60
- Circuits
- 4 000 rpm
- Max speed
- 250 mA
- Current per circuit
- 203.2 mm · 907 g
- Length · weight
- Stator diameter36.58 mm
- Length181.61 mm
- Operating temperature−40 to 121 °C
- Connectionscircular connectors
- Stator diameter36.58 mm
- Length203.2 mm
- Operating temperature−40 to 121 °C
- Connectionscircular connectors
SR45A-AXHS: forty-five-circuit end-of-shaft slip ring
The SR45A-AXHS is an end-of-shaft slip ring with 45 circuits rated at 250 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator. Its rings and brushes are wrought precious metals, with no plating, which minimizes electrical noise; the peak resistance variation is 0.1 Ω. Its stainless steel case is sealed against dust, and circular connectors on rotor and stator carry the circuits. With a 63.49 mm (2.5 in) rotor flange, it is 181.61 mm long, weighs 794 g and runs up to 4 000 rpm, from −40 to 121 °C.
The rotor flange is bolted to the end of the shaft on a 57.15 mm (2.25 in) bolt circle. The sensor wires are brought to the rotor connectors and the data acquisition wires to the stator connectors; the connectors are inserted and secured with a clamping plate. The bearings are permanently lubricated, which eliminates routine cleaning and maintenance.
It is used where many circuits are needed on one shaft, for example to measure strain and temperature on fan and turbine blades, or strain on the blades and in the gearbox of a wind turbine.
SR60A-AXHS: sixty-circuit end-of-shaft slip ring
The SR60A-AXHS is an end-of-shaft slip ring with 60 circuits rated at 250 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator. Its rings and brushes are wrought precious metals, with no plating, which minimizes electrical noise; the peak resistance variation is 0.1 Ω. Its stainless steel case is sealed against dust, and circular connectors on rotor and stator carry the circuits. With a 63.49 mm (2.5 in) rotor flange, it is 203.2 mm long, weighs 907 g and runs up to 4 000 rpm, from −40 to 121 °C.
The rotor flange is bolted to the end of the shaft on a 57.15 mm (2.25 in) bolt circle. The sensor wires are brought to the rotor connectors and the data acquisition wires to the stator connectors; the connectors are inserted and secured with a clamping plate. The bearings are permanently lubricated, which eliminates routine cleaning and maintenance.
It is used where many circuits are needed on one shaft, for example to measure strain and temperature on fan and turbine blades, or strain on the blades and in the gearbox of a wind turbine.
Specifications
| Circuits | 45 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 250 mA |
| Mounting | End of shaft |
| Max speed | 4 000 rpm |
| Rotor diameter | 63.49 mm |
| Dimensions | Ø 36.58 × 181.61 mm |
| Weight | 794 g |
| Operating temperature | −40 to 121 °C |
| Connections | Connector (rotor and stator: circular connectors) |
| Circuits | 60 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 250 mA |
| Mounting | End of shaft |
| Max speed | 4 000 rpm |
| Rotor diameter | 63.49 mm |
| Dimensions | Ø 36.58 × 203.2 mm |
| Weight | 907 g |
| Operating temperature | −40 to 121 °C |
| Connections | Connector (rotor and stator: circular connectors) |
Request a quote
Resources
Datasheets and manuals
Drawings
None for SR45A-AXHS.
CAD models
None for SR45A-AXHS.
Datasheets and manuals
Drawings
None for SR60A-AXHS.
CAD models
Related applications
-
Turbines Fan and turbine blades Strain and temperature from many points on the blades, recorded together while the rotor turns. -
Turbines Wind turbine strain Strain on the blades and in the gearbox of a wind turbine, brought off the rotor by a slip ring or by telemetry. -
Efficiency Vehicle efficiency and power mapping Torque and speed measured at each driveline stage, from engine to wheel, so each power loss has a location.
If 45 or 60 circuits are not the answer
- Around the shaft B-Series
Tubular slip rings that slide over a shaft with no free end: 4 to 8 circuits, bores from 30 to 81.3 mm, open or weatherproof.
- Around the shaft, with speed B-Series
Tubular slip rings that slide over a shaft with no free end: 4 to 8 circuits, bores from 30 to 81.3 mm, open or weatherproof.
- Around the shaft, sealed B-Series
Tubular slip rings that slide over a shaft with no free end: 4 to 8 circuits, bores from 30 to 81.3 mm, open or weatherproof.
A question on this product?
Describe the measurement. An application engineer answers.
More details to give? Use the full contact form.