Michigan Scientific · force and torque transducer
TF Series torque flange for test benches
Torque in a rotating shaft line, from 100 N·m to 50 kN·m, with no contact between rotor and stator.
0.1 kN·m, aluminum body. TF0.1: Datasheet PDF
1 kN·m, aluminum body. TF1: Datasheet PDF
2 kN·m, stainless steel body. TF2: Datasheet PDF
3 kN·m, stainless steel body. TF3: Datasheet PDF
5 kN·m, stainless steel body. TF5: Datasheet PDF
10 kN·m, stainless steel body. TF10: Datasheet PDF
15 kN·m, stainless steel body. TF15: Datasheet PDF
25 kN·m, stainless steel body. TF25: Datasheet PDF
50 kN·m, stainless steel body. TF50: Datasheet PDF
- 0.1 kN·m
- Torque range
- 9 000 rpm
- Max speed
- 126.65 mm
- Outer diameter
- 45 mm
- Length
- 1 kN·m
- Torque range
- 7 000 rpm
- Max speed
- 162 mm
- Outer diameter
- 49 mm
- Length
- 2 kN·m
- Torque range
- 7 000 rpm
- Max speed
- 202 mm
- Outer diameter
- 53 mm
- Length
- 3 kN·m
- Torque range
- 6 000 rpm
- Max speed
- 202 mm
- Outer diameter
- 53 mm
- Length
- 5 kN·m
- Torque range
- 6 000 rpm
- Max speed
- 325 mm
- Outer diameter
- 63 mm
- Length
- 10 kN·m
- Torque range
- 6 000 rpm
- Max speed
- 325 mm
- Outer diameter
- 75 mm
- Length
- 15 kN·m
- Torque range
- 6 000 rpm
- Max speed
- 326 mm
- Outer diameter
- 73 mm
- Length
- 25 kN·m
- Torque range
- 6 000 rpm
- Max speed
- 326 mm
- Outer diameter
- 73 mm
- Length
- 50 kN·m
- Torque range
- 6 000 rpm
- Max speed
- 390 mm
- Outer diameter
- 85 mm
- Length
- Output signal±10 V DC or CAN bus
- Overload protection200 %
- Total thickness45 to 85 mm depending on version
- SealingIP67
01 · The essential
Rotor in the shaft line, stator beside it
The TF has three parts. The rotor goes in the shaft line between two flanges and carries the strain gages and a telemetry transmitter. The stator sits on the fixed part of the test bench, and a receiver unit supplies the power and generates the output signals.
The stator mounts on the frame about 1 to 2 mm from the rotor antenna. It powers the rotor by induction and collects the measurement, sampled at 5.4 kHz.
Check the alignment of the shafts during installation, to keep radial forces on the torque meter low. Angular position and rotational speed are measured as well. Thrust and two bending moments are options.
02 · Specifications
| Torque range | 0.1 kN·m |
|---|---|
| Max rotation speed | 9 000 rpm |
| Material | aluminum |
| Outer diameter | 126.65 mm |
| Length | 45 mm |
| Bolt circle | 84 mm |
| Mounting fasteners | 6 × M8 |
| Type | rotating, mounted inline between two flanges |
| Accuracy | 0.1 % |
| Safe overload | 200 % |
| Sampling | 5.2 kHz, 16 bits |
| Output | ±10 V DC or CAN bus |
| Also measured | angular position and rotational speed |
| Transmission | wireless telemetry, induction powered, no bearing |
| Power supply | 9 to 36 V DC |
| Operating temperature | −40 to 85 °C |
| Protection | IP67 |
| Optional additional axes | Fy, Mx and Mz |
| Torque range | 1 kN·m |
|---|---|
| Max rotation speed | 7 000 rpm |
| Material | aluminum |
| Outer diameter | 162 mm |
| Length | 49 mm |
| Bolt circle | 101.5 mm |
| Mounting fasteners | 8 × M10 |
| Type | rotating, mounted inline between two flanges |
| Accuracy | 0.1 % |
| Safe overload | 200 % |
| Sampling | 5.2 kHz, 16 bits |
| Output | ±10 V DC or CAN bus |
| Also measured | angular position and rotational speed |
| Transmission | wireless telemetry, induction powered, no bearing |
| Power supply | 9 to 36 V DC |
| Operating temperature | −40 to 85 °C |
| Protection | IP67 |
| Optional additional axes | Fy, Mx and Mz |
| Torque range | 2 kN·m |
|---|---|
| Max rotation speed | 7 000 rpm |
| Material | stainless steel |
| Outer diameter | 202 mm |
| Length | 53 mm |
| Bolt circle | 130 mm |
| Mounting fasteners | 8 × M12 |
| Type | rotating, mounted inline between two flanges |
| Accuracy | 0.1 % |
| Safe overload | 200 % |
| Sampling | 5.2 kHz, 16 bits |
| Output | ±10 V DC or CAN bus |
| Also measured | angular position and rotational speed |
| Transmission | wireless telemetry, induction powered, no bearing |
| Power supply | 9 to 36 V DC |
| Operating temperature | −40 to 85 °C |
| Protection | IP67 |
| Optional additional axes | Fy, Mx and Mz |
| Torque range | 3 kN·m |
|---|---|
| Max rotation speed | 6 000 rpm |
| Material | stainless steel |
| Outer diameter | 202 mm |
| Length | 53 mm |
| Bolt circle | 130 mm |
| Mounting fasteners | 8 × M12 |
| Type | rotating, mounted inline between two flanges |
| Accuracy | 0.1 % |
| Safe overload | 200 % |
| Sampling | 5.2 kHz, 16 bits |
| Output | ±10 V DC or CAN bus |
| Also measured | angular position and rotational speed |
| Transmission | wireless telemetry, induction powered, no bearing |
| Power supply | 9 to 36 V DC |
| Operating temperature | −40 to 85 °C |
| Protection | IP67 |
| Optional additional axes | Fy, Mx and Mz |
| Torque range | 5 kN·m |
|---|---|
| Max rotation speed | 6 000 rpm |
| Material | stainless steel |
| Outer diameter | 325 mm |
| Length | 63 mm |
| Bolt circle | 155.5 mm |
| Mounting fasteners | 8 × M14 |
| Type | rotating, mounted inline between two flanges |
| Accuracy | 0.1 % |
| Safe overload | 200 % |
| Sampling | 5.2 kHz, 16 bits |
| Output | ±10 V DC or CAN bus |
| Also measured | angular position and rotational speed |
| Transmission | wireless telemetry, induction powered, no bearing |
| Power supply | 9 to 36 V DC |
| Operating temperature | −40 to 85 °C |
| Protection | IP67 |
| Optional additional axes | Fy, Mx and Mz |
| Torque range | 10 kN·m |
|---|---|
| Max rotation speed | 6 000 rpm |
| Material | stainless steel |
| Outer diameter | 325 mm |
| Length | 75 mm |
| Bolt circle | 196 mm |
| Mounting fasteners | 8 × M16 |
| Type | rotating, mounted inline between two flanges |
| Accuracy | 0.1 % |
| Safe overload | 200 % |
| Sampling | 5.2 kHz, 16 bits |
| Output | ±10 V DC or CAN bus |
| Also measured | angular position and rotational speed |
| Transmission | wireless telemetry, induction powered, no bearing |
| Power supply | 9 to 36 V DC |
| Operating temperature | −40 to 85 °C |
| Protection | IP67 |
| Optional additional axes | Fy, Mx and Mz |
| Torque range | 15 kN·m |
|---|---|
| Max rotation speed | 6 000 rpm |
| Material | stainless steel |
| Outer diameter | 326 mm |
| Length | 73 mm |
| Bolt circle | 288 mm and 206 mm |
| Mounting fasteners | 16 × M18 |
| Type | rotating, mounted inline between two flanges |
| Accuracy | 0.1 % |
| Safe overload | 200 % |
| Sampling | 5.2 kHz, 16 bits |
| Output | ±10 V DC or CAN bus |
| Also measured | angular position and rotational speed |
| Transmission | wireless telemetry, induction powered, no bearing |
| Power supply | 9 to 36 V DC |
| Operating temperature | −40 to 85 °C |
| Protection | IP67 |
| Optional additional axes | Fy, Mx and Mz |
| Torque range | 25 kN·m |
|---|---|
| Max rotation speed | 6 000 rpm |
| Material | stainless steel |
| Outer diameter | 326 mm |
| Length | 73 mm |
| Bolt circle | 288 mm and 206 mm |
| Mounting fasteners | 16 × M18 |
| Type | rotating, mounted inline between two flanges |
| Accuracy | 0.1 % |
| Safe overload | 200 % |
| Sampling | 5.2 kHz, 16 bits |
| Output | ±10 V DC or CAN bus |
| Also measured | angular position and rotational speed |
| Transmission | wireless telemetry, induction powered, no bearing |
| Power supply | 9 to 36 V DC |
| Operating temperature | −40 to 85 °C |
| Protection | IP67 |
| Optional additional axes | Fy, Mx and Mz |
| Torque range | 50 kN·m |
|---|---|
| Max rotation speed | 6 000 rpm |
| Material | stainless steel |
| Outer diameter | 390 mm |
| Length | 85 mm |
| Bolt circle | 350 mm and 250 mm |
| Mounting fasteners | 20 × M20 |
| Type | rotating, mounted inline between two flanges |
| Accuracy | 0.1 % |
| Safe overload | 200 % |
| Sampling | 5.2 kHz, 16 bits |
| Output | ±10 V DC or CAN bus |
| Also measured | angular position and rotational speed |
| Transmission | wireless telemetry, induction powered, no bearing |
| Power supply | 9 to 36 V DC |
| Operating temperature | −40 to 85 °C |
| Protection | IP67 |
| Optional additional axes | Fy, Mx and Mz |
Values from the current product page.
03 · Configure
Request a quote
04 · Resources
Resources
Datasheets and manuals
Drawings
None for this product.
CAD models
None for this product.
06 · Related
Other ways to measure torque
- At the power take-off PTO torque transducer
Torque and speed between the tractor and the implement, ± 5 000 N·m.
- At the wheel TW series wheel torque transducers
Brake and drive torque My, measured while driving.
- On a shaft you cannot wire Wireless telemetry
Torque on half shafts, propshafts and dyno couplings, with no slip ring.
A question on this product?
Describe the measurement. An application engineer answers.
More details to give? Use the full contact form.