SR Series end-of-shaft slip rings
Ten-circuit end-of-shaft slip ring with a 50.8 mm (2 in) rotor and a brush lifter, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof ten-circuit end-of-shaft slip ring with a 50.8 mm (2 in) rotor and contacting seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof ten-circuit end-of-shaft slip ring with a 50.8 mm (2 in) rotor and labyrinth seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Ten-circuit end-of-shaft slip ring with a 63.5 mm (2.5 in) rotor, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof ten-circuit end-of-shaft slip ring with a 63.5 mm (2.5 in) rotor and contacting seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof ten-circuit end-of-shaft slip ring with a 63.5 mm (2.5 in) rotor and labyrinth seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Ten-circuit end-of-shaft slip ring with a 73.7 mm (2.9 in) rotor, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof ten-circuit end-of-shaft slip ring with a 73.7 mm (2.9 in) rotor and contacting seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof ten-circuit end-of-shaft slip ring with a 73.7 mm (2.9 in) rotor and labyrinth seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Ten-circuit end-of-shaft slip ring with a 76.2 mm (3 in) rotor, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof ten-circuit end-of-shaft slip ring with a 76.2 mm (3 in) rotor and contacting seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof ten-circuit end-of-shaft slip ring with a 76.2 mm (3 in) rotor and labyrinth seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Twenty-circuit end-of-shaft slip ring with a 50.8 mm (2 in) rotor, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof twenty-circuit end-of-shaft slip ring with a 50.8 mm (2 in) rotor and contacting seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof twenty-circuit end-of-shaft slip ring with a 50.8 mm (2 in) rotor and labyrinth seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Twenty-circuit end-of-shaft slip ring with a 63.5 mm (2.5 in) rotor, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof twenty-circuit end-of-shaft slip ring with a 63.5 mm (2.5 in) rotor and contacting seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof twenty-circuit end-of-shaft slip ring with a 63.5 mm (2.5 in) rotor and labyrinth seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Twenty-circuit end-of-shaft slip ring with a 73.7 mm (2.9 in) rotor, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof twenty-circuit end-of-shaft slip ring with a 73.7 mm (2.9 in) rotor and contacting seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof twenty-circuit end-of-shaft slip ring with a 73.7 mm (2.9 in) rotor and labyrinth seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Twenty-circuit end-of-shaft slip ring with a 76.2 mm (3 in) rotor, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof twenty-circuit end-of-shaft slip ring with a 76.2 mm (3 in) rotor and contacting seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof twenty-circuit end-of-shaft slip ring with a 76.2 mm (3 in) rotor and labyrinth seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
36-circuit end-of-shaft slip ring with a 50.8 mm (2 in) rotor, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof 36-circuit end-of-shaft slip ring with a 50.8 mm (2 in) rotor and contacting seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof 36-circuit end-of-shaft slip ring with a 50.8 mm (2 in) rotor and labyrinth seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
36-circuit end-of-shaft slip ring with a 63.5 mm (2.5 in) rotor, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof 36-circuit end-of-shaft slip ring with a 63.5 mm (2.5 in) rotor and contacting seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof 36-circuit end-of-shaft slip ring with a 63.5 mm (2.5 in) rotor and labyrinth seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
36-circuit end-of-shaft slip ring with a 73.7 mm (2.9 in) rotor, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof 36-circuit end-of-shaft slip ring with a 73.7 mm (2.9 in) rotor and contacting seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof 36-circuit end-of-shaft slip ring with a 73.7 mm (2.9 in) rotor and labyrinth seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
36-circuit end-of-shaft slip ring with a 76.2 mm (3 in) rotor, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof 36-circuit end-of-shaft slip ring with a 76.2 mm (3 in) rotor and contacting seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Weatherproof 36-circuit end-of-shaft slip ring with a 76.2 mm (3 in) rotor and labyrinth seals, for low-level signals: strain gages, thermocouples, accelerometers and low voltages.
Model SR10M
- 10
- Circuits
- 12 000 rpm
- Max speed
- 50.8 mm
- Rotor diameter
- 42.7 mm · 184 g
- Length · weight
- 10
- Circuits
- 2 000 rpm
- Max speed
- 50.8 mm
- Rotor diameter
- weatherproof
- Contacting rotary seals
- 10
- Circuits
- 12 000 rpm
- Max speed
- 50.8 mm
- Rotor diameter
- weatherproof
- Labyrinth seals
- 10
- Circuits
- 12 000 rpm
- Max speed
- 63.5 mm
- Rotor diameter
- 10
- Circuits
- 2 000 rpm
- Max speed
- 63.5 mm
- Rotor diameter
- weatherproof
- Contacting rotary seals
- 10
- Circuits
- 12 000 rpm
- Max speed
- 63.5 mm
- Rotor diameter
- weatherproof
- Labyrinth seals
- 10
- Circuits
- 12 000 rpm
- Max speed
- 73.7 mm
- Rotor diameter
- 10
- Circuits
- 2 000 rpm
- Max speed
- 73.7 mm
- Rotor diameter
- weatherproof
- Contacting rotary seals
- 10
- Circuits
- 12 000 rpm
- Max speed
- 73.7 mm
- Rotor diameter
- weatherproof
- Labyrinth seals
- 10
- Circuits
- 12 000 rpm
- Max speed
- 76.2 mm
- Rotor diameter
- 10
- Circuits
- 2 000 rpm
- Max speed
- 76.2 mm
- Rotor diameter
- weatherproof
- Contacting rotary seals
- 10
- Circuits
- 12 000 rpm
- Max speed
- 76.2 mm
- Rotor diameter
- weatherproof
- Labyrinth seals
- 20
- Circuits
- 4 000 rpm
- Max speed
- 50.8 mm
- Rotor diameter
- 56.6 mm · 204 g
- Length · weight
- 20
- Circuits
- 2 000 rpm
- Max speed
- 50.8 mm
- Rotor diameter
- weatherproof
- Contacting rotary seals
- 20
- Circuits
- 4 000 rpm
- Max speed
- 50.8 mm
- Rotor diameter
- weatherproof
- Labyrinth seals
- 20
- Circuits
- 4 000 rpm
- Max speed
- 63.5 mm
- Rotor diameter
- 20
- Circuits
- 2 000 rpm
- Max speed
- 63.5 mm
- Rotor diameter
- weatherproof
- Contacting rotary seals
- 20
- Circuits
- 4 000 rpm
- Max speed
- 63.5 mm
- Rotor diameter
- weatherproof
- Labyrinth seals
- 20
- Circuits
- 4 000 rpm
- Max speed
- 73.7 mm
- Rotor diameter
- 20
- Circuits
- 2 000 rpm
- Max speed
- 73.7 mm
- Rotor diameter
- weatherproof
- Contacting rotary seals
- 20
- Circuits
- 4 000 rpm
- Max speed
- 73.7 mm
- Rotor diameter
- weatherproof
- Labyrinth seals
- 20
- Circuits
- 4 000 rpm
- Max speed
- 76.2 mm
- Rotor diameter
- 20
- Circuits
- 2 000 rpm
- Max speed
- 76.2 mm
- Rotor diameter
- weatherproof
- Contacting rotary seals
- 20
- Circuits
- 4 000 rpm
- Max speed
- 76.2 mm
- Rotor diameter
- weatherproof
- Labyrinth seals
- 36
- Circuits
- 2 400 rpm
- Max speed
- 50.8 mm
- Rotor diameter
- 89.2 mm · 255 g
- Length · weight
- 36
- Circuits
- 2 000 rpm
- Max speed
- 50.8 mm
- Rotor diameter
- weatherproof
- Contacting rotary seals
- 36
- Circuits
- 2 400 rpm
- Max speed
- 50.8 mm
- Rotor diameter
- weatherproof
- Labyrinth seals
- 36
- Circuits
- 2 400 rpm
- Max speed
- 63.5 mm
- Rotor diameter
- 36
- Circuits
- 2 000 rpm
- Max speed
- 63.5 mm
- Rotor diameter
- weatherproof
- Contacting rotary seals
- 36
- Circuits
- 2 400 rpm
- Max speed
- 63.5 mm
- Rotor diameter
- weatherproof
- Labyrinth seals
- 36
- Circuits
- 2 400 rpm
- Max speed
- 73.7 mm
- Rotor diameter
- 36
- Circuits
- 2 000 rpm
- Max speed
- 73.7 mm
- Rotor diameter
- weatherproof
- Contacting rotary seals
- 36
- Circuits
- 2 400 rpm
- Max speed
- 73.7 mm
- Rotor diameter
- weatherproof
- Labyrinth seals
- 36
- Circuits
- 2 400 rpm
- Max speed
- 76.2 mm
- Rotor diameter
- 36
- Circuits
- 2 000 rpm
- Max speed
- 76.2 mm
- Rotor diameter
- weatherproof
- Contacting rotary seals
- 36
- Circuits
- 2 400 rpm
- Max speed
- 76.2 mm
- Rotor diameter
- weatherproof
- Labyrinth seals
- Stator diameter34.93 mm
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsNone (sealed against dust)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsContacting rotary seals (W)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsLabyrinth seals (B)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsNone (sealed against dust)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsContacting rotary seals (W)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsLabyrinth seals (B)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsNone (sealed against dust)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsContacting rotary seals (W)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsLabyrinth seals (B)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsNone (sealed against dust)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsContacting rotary seals (W)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsLabyrinth seals (B)
- Stator diameter34.93 mm
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsNone (sealed against dust)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsContacting rotary seals (W)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsLabyrinth seals (B)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsNone (sealed against dust)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsContacting rotary seals (W)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsLabyrinth seals (B)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsNone (sealed against dust)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsContacting rotary seals (W)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsLabyrinth seals (B)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsNone (sealed against dust)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsContacting rotary seals (W)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsLabyrinth seals (B)
- Stator diameter36.58 mm
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsNone (sealed against dust)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsContacting rotary seals (W)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsLabyrinth seals (B)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsNone (sealed against dust)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsContacting rotary seals (W)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsLabyrinth seals (B)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsNone (sealed against dust)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsContacting rotary seals (W)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsLabyrinth seals (B)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsNone (sealed against dust)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsContacting rotary seals (W)
- Operating temperature−40 to 121 °C
- Contactscolor-coded solder terminals
- SealsLabyrinth seals (B)
Ten-circuit end-of-shaft slip ring with brush lifter, 50.8 mm rotor
The SR10M is an end-of-shaft slip ring with ten circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. A manual brush lifter lifts the brushes off the rings while the slip ring keeps turning, reducing wear. Its stainless steel case is sealed against dust. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. With a 50.8 mm (2 in) rotor, it is 42.7 mm (1.68 in) long to the top of the brush lifter, weighs 184 g and runs up to 12 000 rpm, from −40 to 121 °C.
On installation, the rotor flange is mounted to the end of the shaft, through an adapter if needed, with three #8-32 screws 120° apart on a 43.2 mm (1.700 in) bolt circle. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor; its rotor pilots onto AMP-TC modules that amplify the thermocouples on the rotating side.
Weatherproof ten-circuit end-of-shaft slip ring, 50.8 mm rotor, contacting seals
The SR10MW is an end-of-shaft slip ring with ten circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Contacting rotary seals (W) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor is 50.8 mm (2 in) in diameter; it runs up to 2 000 rpm, against 12 000 rpm without these seals, from −40 to 121 °C.
On installation, the rotor flange is mounted to the end of the shaft, through an adapter if needed, with three #8-32 screws 120° apart on a 43.2 mm (1.700 in) bolt circle. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Weatherproof ten-circuit end-of-shaft slip ring, 50.8 mm rotor, labyrinth seals
The SR10MB is an end-of-shaft slip ring with ten circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Non-contacting labyrinth seals (B) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor is 50.8 mm (2 in) in diameter; it runs up to 12 000 rpm, from −40 to 121 °C.
On installation, the rotor flange is mounted to the end of the shaft, through an adapter if needed, with three #8-32 screws 120° apart on a 43.2 mm (1.700 in) bolt circle. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Ten-circuit end-of-shaft slip ring, 63.5 mm rotor
The SR10A is an end-of-shaft slip ring with ten circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Its stainless steel case is sealed against dust. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code A) is 63.5 mm (2.5 in) in diameter, against 50.8 mm on the SR10M; it runs up to 12 000 rpm, from −40 to 121 °C.
On installation, the 63.5 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor; its rotor pilots onto AMP-TC modules that amplify the thermocouples on the rotating side.
Weatherproof ten-circuit end-of-shaft slip ring, 63.5 mm rotor, contacting seals
The SR10AW is an end-of-shaft slip ring with ten circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Contacting rotary seals (W) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code A) is 63.5 mm (2.5 in) in diameter, against 50.8 mm on the SR10M; it runs up to 2 000 rpm, against 12 000 rpm without these seals, from −40 to 121 °C.
On installation, the 63.5 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
As an SR10AW/T512/AX2, with a tachometer circuit and connectors on rotor and stator, it is the slip ring of the 6 in Wheel Instrumentation Package WIP6-SG-TC2K.
Weatherproof ten-circuit end-of-shaft slip ring, 63.5 mm rotor, labyrinth seals
The SR10AB is an end-of-shaft slip ring with ten circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Non-contacting labyrinth seals (B) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code A) is 63.5 mm (2.5 in) in diameter, against 50.8 mm on the SR10M; it runs up to 12 000 rpm, from −40 to 121 °C.
On installation, the 63.5 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Ten-circuit end-of-shaft slip ring, 73.7 mm rotor
The SR10G is an end-of-shaft slip ring with ten circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Its stainless steel case is sealed against dust. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code G) is 73.7 mm (2.9 in) in diameter, against 50.8 mm on the SR10M; it runs up to 12 000 rpm, from −40 to 121 °C.
On installation, the 73.7 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor; its rotor pilots onto AMP-TC modules that amplify the thermocouples on the rotating side.
Weatherproof ten-circuit end-of-shaft slip ring, 73.7 mm rotor, contacting seals
The SR10GW is an end-of-shaft slip ring with ten circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Contacting rotary seals (W) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code G) is 73.7 mm (2.9 in) in diameter, against 50.8 mm on the SR10M; it runs up to 2 000 rpm, against 12 000 rpm without these seals, from −40 to 121 °C.
On installation, the 73.7 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Weatherproof ten-circuit end-of-shaft slip ring, 73.7 mm rotor, labyrinth seals
The SR10GB is an end-of-shaft slip ring with ten circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Non-contacting labyrinth seals (B) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code G) is 73.7 mm (2.9 in) in diameter, against 50.8 mm on the SR10M; it runs up to 12 000 rpm, from −40 to 121 °C.
On installation, the 73.7 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Ten-circuit end-of-shaft slip ring, 76.2 mm rotor
The SR10Y is an end-of-shaft slip ring with ten circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Its stainless steel case is sealed against dust. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code Y) is 76.2 mm (3 in) in diameter, against 50.8 mm on the SR10M; it runs up to 12 000 rpm, from −40 to 121 °C.
On installation, the 76.2 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor; its rotor pilots onto AMP-TC modules that amplify the thermocouples on the rotating side.
Weatherproof ten-circuit end-of-shaft slip ring, 76.2 mm rotor, contacting seals
The SR10YW is an end-of-shaft slip ring with ten circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Contacting rotary seals (W) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code Y) is 76.2 mm (3 in) in diameter, against 50.8 mm on the SR10M; it runs up to 2 000 rpm, against 12 000 rpm without these seals, from −40 to 121 °C.
On installation, the 76.2 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Weatherproof ten-circuit end-of-shaft slip ring, 76.2 mm rotor, labyrinth seals
The SR10YB is an end-of-shaft slip ring with ten circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Non-contacting labyrinth seals (B) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code Y) is 76.2 mm (3 in) in diameter, against 50.8 mm on the SR10M; it runs up to 12 000 rpm, from −40 to 121 °C.
On installation, the 76.2 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Twenty-circuit end-of-shaft slip ring, 50.8 mm rotor
The SR20M is an end-of-shaft slip ring with twenty circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Its stainless steel case is sealed against dust. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. With a 50.8 mm (2 in) rotor, it is 56.6 mm (2.23 in) long, weighs 204 g and runs up to 4 000 rpm, from −40 to 121 °C.
On installation, the rotor flange is mounted to the end of the shaft, through an adapter if needed, with three #8-32 screws 120° apart on a 43.2 mm (1.700 in) bolt circle. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor; its rotor pilots onto AMP-TC modules that amplify the thermocouples on the rotating side.
Weatherproof twenty-circuit end-of-shaft slip ring, 50.8 mm rotor, contacting seals
The SR20MW is an end-of-shaft slip ring with twenty circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Contacting rotary seals (W) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor is 50.8 mm (2 in) in diameter; it runs up to 2 000 rpm, against 4 000 rpm without these seals, from −40 to 121 °C.
On installation, the rotor flange is mounted to the end of the shaft, through an adapter if needed, with three #8-32 screws 120° apart on a 43.2 mm (1.700 in) bolt circle. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Weatherproof twenty-circuit end-of-shaft slip ring, 50.8 mm rotor, labyrinth seals
The SR20MB is an end-of-shaft slip ring with twenty circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Non-contacting labyrinth seals (B) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor is 50.8 mm (2 in) in diameter; it runs up to 4 000 rpm, from −40 to 121 °C.
On installation, the rotor flange is mounted to the end of the shaft, through an adapter if needed, with three #8-32 screws 120° apart on a 43.2 mm (1.700 in) bolt circle. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Twenty-circuit end-of-shaft slip ring, 63.5 mm rotor
The SR20A is an end-of-shaft slip ring with twenty circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Its stainless steel case is sealed against dust. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code A) is 63.5 mm (2.5 in) in diameter, against 50.8 mm on the SR20M; it runs up to 4 000 rpm, from −40 to 121 °C.
On installation, the 63.5 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor; its rotor pilots onto AMP-TC modules that amplify the thermocouples on the rotating side.
Weatherproof twenty-circuit end-of-shaft slip ring, 63.5 mm rotor, contacting seals
The SR20AW is an end-of-shaft slip ring with twenty circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Contacting rotary seals (W) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code A) is 63.5 mm (2.5 in) in diameter, against 50.8 mm on the SR20M; it runs up to 2 000 rpm, against 4 000 rpm without these seals, from −40 to 121 °C.
On installation, the 63.5 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Weatherproof twenty-circuit end-of-shaft slip ring, 63.5 mm rotor, labyrinth seals
The SR20AB is an end-of-shaft slip ring with twenty circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Non-contacting labyrinth seals (B) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code A) is 63.5 mm (2.5 in) in diameter, against 50.8 mm on the SR20M; it runs up to 4 000 rpm, from −40 to 121 °C.
On installation, the 63.5 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Twenty-circuit end-of-shaft slip ring, 73.7 mm rotor
The SR20G is an end-of-shaft slip ring with twenty circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Its stainless steel case is sealed against dust. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code G) is 73.7 mm (2.9 in) in diameter, against 50.8 mm on the SR20M; it runs up to 4 000 rpm, from −40 to 121 °C.
On installation, the 73.7 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor; its rotor pilots onto AMP-TC modules that amplify the thermocouples on the rotating side.
Weatherproof twenty-circuit end-of-shaft slip ring, 73.7 mm rotor, contacting seals
The SR20GW is an end-of-shaft slip ring with twenty circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Contacting rotary seals (W) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code G) is 73.7 mm (2.9 in) in diameter, against 50.8 mm on the SR20M; it runs up to 2 000 rpm, against 4 000 rpm without these seals, from −40 to 121 °C.
On installation, the 73.7 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Weatherproof twenty-circuit end-of-shaft slip ring, 73.7 mm rotor, labyrinth seals
The SR20GB is an end-of-shaft slip ring with twenty circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Non-contacting labyrinth seals (B) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code G) is 73.7 mm (2.9 in) in diameter, against 50.8 mm on the SR20M; it runs up to 4 000 rpm, from −40 to 121 °C.
On installation, the 73.7 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Twenty-circuit end-of-shaft slip ring, 76.2 mm rotor
The SR20Y is an end-of-shaft slip ring with twenty circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Its stainless steel case is sealed against dust. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code Y) is 76.2 mm (3 in) in diameter, against 50.8 mm on the SR20M; it runs up to 4 000 rpm, from −40 to 121 °C.
On installation, the 76.2 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor; its rotor pilots onto AMP-TC modules that amplify the thermocouples on the rotating side.
Weatherproof twenty-circuit end-of-shaft slip ring, 76.2 mm rotor, contacting seals
The SR20YW is an end-of-shaft slip ring with twenty circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Contacting rotary seals (W) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code Y) is 76.2 mm (3 in) in diameter, against 50.8 mm on the SR20M; it runs up to 2 000 rpm, against 4 000 rpm without these seals, from −40 to 121 °C.
On installation, the 76.2 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Weatherproof twenty-circuit end-of-shaft slip ring, 76.2 mm rotor, labyrinth seals
The SR20YB is an end-of-shaft slip ring with twenty circuits rated at 500 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Non-contacting labyrinth seals (B) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code Y) is 76.2 mm (3 in) in diameter, against 50.8 mm on the SR20M; it runs up to 4 000 rpm, from −40 to 121 °C.
On installation, the 76.2 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
36-circuit end-of-shaft slip ring, 50.8 mm rotor
The SR36M is an end-of-shaft slip ring with 36 circuits rated at 250 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Its stainless steel case is sealed against dust. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. With a 50.8 mm (2 in) rotor, it is 89.2 mm (3.51 in) long, weighs 255 g and runs up to 2 400 rpm, from −40 to 121 °C.
On installation, the rotor flange is mounted to the end of the shaft, through an adapter if needed, with three #8-32 screws 120° apart on a 43.2 mm (1.700 in) bolt circle. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified.
In a validation test, an SR36M spinning at 900 rpm carried a Gigabit Ethernet link, a file passing at 111 MB/s with no error; it is also used for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Weatherproof 36-circuit end-of-shaft slip ring, 50.8 mm rotor, contacting seals
The SR36MW is an end-of-shaft slip ring with 36 circuits rated at 250 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Contacting rotary seals (W) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor is 50.8 mm (2 in) in diameter; it runs up to 2 000 rpm, against 2 400 rpm without these seals, from −40 to 121 °C.
On installation, the rotor flange is mounted to the end of the shaft, through an adapter if needed, with three #8-32 screws 120° apart on a 43.2 mm (1.700 in) bolt circle. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Weatherproof 36-circuit end-of-shaft slip ring, 50.8 mm rotor, labyrinth seals
The SR36MB is an end-of-shaft slip ring with 36 circuits rated at 250 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Non-contacting labyrinth seals (B) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor is 50.8 mm (2 in) in diameter; it runs up to 2 400 rpm, from −40 to 121 °C.
On installation, the rotor flange is mounted to the end of the shaft, through an adapter if needed, with three #8-32 screws 120° apart on a 43.2 mm (1.700 in) bolt circle. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
36-circuit end-of-shaft slip ring, 63.5 mm rotor
The SR36A is an end-of-shaft slip ring with 36 circuits rated at 250 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Its stainless steel case is sealed against dust. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code A) is 63.5 mm (2.5 in) in diameter, against 50.8 mm on the SR36M; it runs up to 2 400 rpm, from −40 to 121 °C.
On installation, the 63.5 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor; its rotor pilots onto AMP-TC modules that amplify the thermocouples on the rotating side.
Weatherproof 36-circuit end-of-shaft slip ring, 63.5 mm rotor, contacting seals
The SR36AW is an end-of-shaft slip ring with 36 circuits rated at 250 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Contacting rotary seals (W) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code A) is 63.5 mm (2.5 in) in diameter, against 50.8 mm on the SR36M; it runs up to 2 000 rpm, against 2 400 rpm without these seals, from −40 to 121 °C.
On installation, the 63.5 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Weatherproof 36-circuit end-of-shaft slip ring, 63.5 mm rotor, labyrinth seals
The SR36AB is an end-of-shaft slip ring with 36 circuits rated at 250 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Non-contacting labyrinth seals (B) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code A) is 63.5 mm (2.5 in) in diameter, against 50.8 mm on the SR36M; it runs up to 2 400 rpm, from −40 to 121 °C.
On installation, the 63.5 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
36-circuit end-of-shaft slip ring, 73.7 mm rotor
The SR36G is an end-of-shaft slip ring with 36 circuits rated at 250 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Its stainless steel case is sealed against dust. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code G) is 73.7 mm (2.9 in) in diameter, against 50.8 mm on the SR36M; it runs up to 2 400 rpm, from −40 to 121 °C.
On installation, the 73.7 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor; its rotor pilots onto AMP-TC modules that amplify the thermocouples on the rotating side.
Weatherproof 36-circuit end-of-shaft slip ring, 73.7 mm rotor, contacting seals
The SR36GW is an end-of-shaft slip ring with 36 circuits rated at 250 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Contacting rotary seals (W) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code G) is 73.7 mm (2.9 in) in diameter, against 50.8 mm on the SR36M; it runs up to 2 000 rpm, against 2 400 rpm without these seals, from −40 to 121 °C.
On installation, the 73.7 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Weatherproof 36-circuit end-of-shaft slip ring, 73.7 mm rotor, labyrinth seals
The SR36GB is an end-of-shaft slip ring with 36 circuits rated at 250 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Non-contacting labyrinth seals (B) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code G) is 73.7 mm (2.9 in) in diameter, against 50.8 mm on the SR36M; it runs up to 2 400 rpm, from −40 to 121 °C.
On installation, the 73.7 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
36-circuit end-of-shaft slip ring, 76.2 mm rotor
The SR36Y is an end-of-shaft slip ring with 36 circuits rated at 250 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Its stainless steel case is sealed against dust. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code Y) is 76.2 mm (3 in) in diameter, against 50.8 mm on the SR36M; it runs up to 2 400 rpm, from −40 to 121 °C.
On installation, the 76.2 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor; its rotor pilots onto AMP-TC modules that amplify the thermocouples on the rotating side.
Weatherproof 36-circuit end-of-shaft slip ring, 76.2 mm rotor, contacting seals
The SR36YW is an end-of-shaft slip ring with 36 circuits rated at 250 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Contacting rotary seals (W) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code Y) is 76.2 mm (3 in) in diameter, against 50.8 mm on the SR36M; it runs up to 2 000 rpm, against 2 400 rpm without these seals, from −40 to 121 °C.
On installation, the 76.2 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Weatherproof 36-circuit end-of-shaft slip ring, 76.2 mm rotor, labyrinth seals
The SR36YB is an end-of-shaft slip ring with 36 circuits rated at 250 mA. It mounts on the end of a rotating shaft and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator through precious metal rings and brushes, with a peak noise of 0.1 Ω. Non-contacting labyrinth seals (B) are added to its dust-sealed stainless steel case. Color-coded solder terminals sit on rotor and stator, and circular connectors are optional. Its rotor (code Y) is 76.2 mm (3 in) in diameter, against 50.8 mm on the SR36M; it runs up to 2 400 rpm, from −40 to 121 °C.
On installation, the 76.2 mm rotor flange is mounted to the end of the shaft, through an adapter if needed. Sensor wires run along the shaft, or through a hollow shaft and a slot machined in it or in the adapter, to the rotor terminals. The bearings are lubricated for life; below −18 °C (0 °F), a low-temperature lubricant is specified. For a weatherproof stator connection, the optional circular connector is sealed at the rear of the plug with RTV silicone or a sealing backshell.
It is used, for example, for thermocouples on crankshaft bearings on an engine dynamometer or on an air conditioning compressor.
Specifications
| Circuits | 10 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 12 000 rpm |
| Rotor diameter | 50.8 mm |
| Seals | None (sealed against dust) |
| Dimensions | Ø 34.93 × 42.7 mm |
| Weight | 184 g |
| Operating temperature | −40 to 121 °C |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 10 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 2 000 rpm |
| Rotor diameter | 50.8 mm |
| Seals | Contacting rotary seals (W) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 10 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 12 000 rpm |
| Rotor diameter | 50.8 mm |
| Seals | Labyrinth seals (B) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 10 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 12 000 rpm |
| Rotor diameter | 63.5 mm |
| Seals | None (sealed against dust) |
| Operating temperature | −40 to 121 °C |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 10 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 2 000 rpm |
| Rotor diameter | 63.5 mm |
| Seals | Contacting rotary seals (W) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 10 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 12 000 rpm |
| Rotor diameter | 63.5 mm |
| Seals | Labyrinth seals (B) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 10 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 12 000 rpm |
| Rotor diameter | 73.7 mm |
| Seals | None (sealed against dust) |
| Operating temperature | −40 to 121 °C |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 10 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 2 000 rpm |
| Rotor diameter | 73.7 mm |
| Seals | Contacting rotary seals (W) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 10 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 12 000 rpm |
| Rotor diameter | 73.7 mm |
| Seals | Labyrinth seals (B) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 10 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 12 000 rpm |
| Rotor diameter | 76.2 mm |
| Seals | None (sealed against dust) |
| Operating temperature | −40 to 121 °C |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 10 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 2 000 rpm |
| Rotor diameter | 76.2 mm |
| Seals | Contacting rotary seals (W) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 10 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 12 000 rpm |
| Rotor diameter | 76.2 mm |
| Seals | Labyrinth seals (B) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 20 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 4 000 rpm |
| Rotor diameter | 50.8 mm |
| Seals | None (sealed against dust) |
| Dimensions | Ø 34.93 × 56.6 mm |
| Weight | 204 g |
| Operating temperature | −40 to 121 °C |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 20 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 2 000 rpm |
| Rotor diameter | 50.8 mm |
| Seals | Contacting rotary seals (W) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 20 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 4 000 rpm |
| Rotor diameter | 50.8 mm |
| Seals | Labyrinth seals (B) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 20 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 4 000 rpm |
| Rotor diameter | 63.5 mm |
| Seals | None (sealed against dust) |
| Operating temperature | −40 to 121 °C |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 20 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 2 000 rpm |
| Rotor diameter | 63.5 mm |
| Seals | Contacting rotary seals (W) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 20 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 4 000 rpm |
| Rotor diameter | 63.5 mm |
| Seals | Labyrinth seals (B) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 20 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 4 000 rpm |
| Rotor diameter | 73.7 mm |
| Seals | None (sealed against dust) |
| Operating temperature | −40 to 121 °C |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 20 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 2 000 rpm |
| Rotor diameter | 73.7 mm |
| Seals | Contacting rotary seals (W) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 20 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 4 000 rpm |
| Rotor diameter | 73.7 mm |
| Seals | Labyrinth seals (B) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 20 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 4 000 rpm |
| Rotor diameter | 76.2 mm |
| Seals | None (sealed against dust) |
| Operating temperature | −40 to 121 °C |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 20 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 2 000 rpm |
| Rotor diameter | 76.2 mm |
| Seals | Contacting rotary seals (W) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 20 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 500 mA |
| Mounting | End of shaft |
| Max speed | 4 000 rpm |
| Rotor diameter | 76.2 mm |
| Seals | Labyrinth seals (B) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 36 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 250 mA |
| Mounting | End of shaft |
| Max speed | 2 400 rpm |
| Rotor diameter | 50.8 mm |
| Seals | None (sealed against dust) |
| Dimensions | Ø 36.58 × 89.2 mm |
| Weight | 255 g |
| Operating temperature | −40 to 121 °C |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 36 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 250 mA |
| Mounting | End of shaft |
| Max speed | 2 000 rpm |
| Rotor diameter | 50.8 mm |
| Seals | Contacting rotary seals (W) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 36 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 250 mA |
| Mounting | End of shaft |
| Max speed | 2 400 rpm |
| Rotor diameter | 50.8 mm |
| Seals | Labyrinth seals (B) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 36 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 250 mA |
| Mounting | End of shaft |
| Max speed | 2 400 rpm |
| Rotor diameter | 63.5 mm |
| Seals | None (sealed against dust) |
| Operating temperature | −40 to 121 °C |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 36 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 250 mA |
| Mounting | End of shaft |
| Max speed | 2 000 rpm |
| Rotor diameter | 63.5 mm |
| Seals | Contacting rotary seals (W) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 36 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 250 mA |
| Mounting | End of shaft |
| Max speed | 2 400 rpm |
| Rotor diameter | 63.5 mm |
| Seals | Labyrinth seals (B) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 36 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 250 mA |
| Mounting | End of shaft |
| Max speed | 2 400 rpm |
| Rotor diameter | 73.7 mm |
| Seals | None (sealed against dust) |
| Operating temperature | −40 to 121 °C |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 36 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 250 mA |
| Mounting | End of shaft |
| Max speed | 2 000 rpm |
| Rotor diameter | 73.7 mm |
| Seals | Contacting rotary seals (W) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 36 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 250 mA |
| Mounting | End of shaft |
| Max speed | 2 400 rpm |
| Rotor diameter | 73.7 mm |
| Seals | Labyrinth seals (B) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 36 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 250 mA |
| Mounting | End of shaft |
| Max speed | 2 400 rpm |
| Rotor diameter | 76.2 mm |
| Seals | None (sealed against dust) |
| Operating temperature | −40 to 121 °C |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 36 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 250 mA |
| Mounting | End of shaft |
| Max speed | 2 000 rpm |
| Rotor diameter | 76.2 mm |
| Seals | Contacting rotary seals (W) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
| Circuits | 36 |
|---|---|
| Rotation sensor | None |
| Embedded amplifier | None |
| Max peak contact noise | ≤ 100 mΩ |
| Current per circuit | 250 mA |
| Mounting | End of shaft |
| Max speed | 2 400 rpm |
| Rotor diameter | 76.2 mm |
| Seals | Labyrinth seals (B) |
| Operating temperature | −40 to 121 °C |
| Protection | Weatherproof |
| Connections | Connector · Solder terminals (rotor and stator: solder terminals; connector optional) |
Resources
Datasheets and manuals
CAD models
Datasheets and manuals
Datasheets and manuals
Datasheets and manuals
Datasheets and manuals
Datasheets and manuals
Datasheets and manuals
Datasheets and manuals
Datasheets and manuals
Datasheets and manuals
Datasheets and manuals
Datasheets and manuals
Datasheets and manuals
Drawings
CAD models
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
CAD models
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Datasheets and manuals
Drawings
Related applications
-
Temperature Temperature on rotating parts The temperature of a bearing, a compressor or a brake rotor, read while the part rotates under load. -
Temperature Brake disc temperature Disc and hub temperatures read on the turning wheel, through a wheel slip ring or a telemetry package. -
Test rig Gigabit Ethernet through a slip ring A Gigabit Ethernet link passed through a spinning slip ring, validated by a file transfer with no error. -
Efficiency Vehicle efficiency and power mapping Torque and speed measured at each driveline stage, from engine to wheel, so each power loss has a location.
If the SR Series is not the one
- Shaft speed as well SR/E60 Series
End of shaft, up to 10 circuits with a 60 ppr encoder, 6 000 rpm.
- Angular position as well SR/PE512 Series
End of shaft, up to 10 circuits with a 512 ppr quadrature encoder and index.
- Encoder and connectors SR/ERT Series
10, 20 or 36 circuits, with an optional encoder or resolver.
A question on this product?
Describe the measurement. An application engineer answers.
More details to give? Use the full contact form.