Name: B7-T-1.2W tubular slip ring
Brand: Michigan Scientific
SKU: B7-T-1.2W

Four-circuit tubular slip ring, 2 in bore

The B4-2 is a tubular slip ring with four circuits rated at 1 A. It mounts on the shaft, which passes through its 50.8 mm (2 in) bore, and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator. Its rings are solid silver alloy and its brushes silver-graphite. The rotor carries color-coded solder terminals with redundant back-up terminals, and the stator a connector supplied with its mating connector. It is 26.9 mm wide and runs up to 7 000 rpm, from −40 to 121 °C.

On installation, the rotor is secured to the shaft with six #8-32 set screws, square and concentric to the axis of rotation; a bushing adapts it to shafts smaller than 50.8 mm. Sensor wires run along the outside of the shaft and through slots in the rotor to the solder terminals, in stranded wire of 24 AWG at most, then are secured to the shaft and coated with RTV silicone. The stator is held by a flexible restraint, such as a small cable, a spring or a wire tie, rather than by its cable. The silver contacts are wear parts: they are inspected periodically and last about 100 million revolutions under ideal conditions.

It is typically used on automotive drive shafts, for example to measure prop shaft torque at the transmission output or half shaft torque.

Six-circuit tubular slip ring, 2 in bore

The B6-2 is a tubular slip ring with six circuits rated at 1 A. It mounts on the shaft, which passes through its 50.8 mm (2 in) bore, and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator. Its rings are solid silver alloy and its brushes silver-graphite. The rotor carries color-coded solder terminals with redundant back-up terminals, and the stator a Bendix PT02E-10-6P connector, supplied with its mating connector. It is 26.9 mm wide and runs up to 7 000 rpm, from −40 to 121 °C.

On installation, the rotor is secured to the shaft with six #8-32 set screws, square and concentric to the axis of rotation; a bushing adapts it to shafts smaller than 50.8 mm. Sensor wires run along the outside of the shaft and through slots in the rotor to the solder terminals, in stranded wire of 24 AWG at most, then are secured to the shaft and coated with RTV silicone. The stator is held by a flexible restraint, such as a small cable, a spring or a wire tie, rather than by its cable. The silver contacts are wear parts: they are inspected periodically and last about 100 million revolutions under ideal conditions.

It is used on automotive drive shafts, for example to measure prop shaft torque at the transmission output, half shaft torque, or torque and axial force on the same drive shaft.

Eight-circuit tubular slip ring, 2 in bore

The B8-2 is a tubular slip ring with eight circuits rated at 1 A. It mounts on the shaft, which passes through its 50.8 mm (2 in) bore, and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator. Its rings are solid silver alloy and its brushes silver-graphite. The rotor carries color-coded solder terminals and the stator a connector. It is 26.9 mm wide, weighs 0.9 kg and runs up to 7 000 rpm, from −40 to 121 °C.

On installation, the rotor is secured to the shaft with six #8-32 set screws, square and concentric to the axis of rotation; a bushing adapts it to shafts smaller than 50.8 mm. Sensor wires run along the outside of the shaft and through slots in the rotor to the solder terminals, in stranded wire of 24 AWG at most, then are secured to the shaft and coated with RTV silicone. The stator is held by a flexible restraint, such as a small cable, a spring or a wire tie, rather than by its cable. The silver contacts are wear parts: they are inspected periodically and last about 100 million revolutions under ideal conditions.

It is used on automotive drive shafts, prop shafts and half shafts, when more circuits are needed than on the B4-2 or B6-2.

Four-circuit tubular slip ring with speed encoder

The B4-2/E60 is the four-circuit B-Series tubular slip ring with a built-in speed encoder. It mounts on the shaft, which passes through its 50.8 mm (2 in) bore, and carries strain gages, thermocouples, accelerometers and low voltages through four circuits rated at 1 A. The encoder is a Hall-effect sensor that delivers a 60 pulse-per-revolution, TTL-compatible 5 V square wave, so speed is measured down to 0 rpm; it is powered from 5.5 to 45 V DC. It is 33 mm long and runs up to 7 000 rpm, from −40 to 121 °C.

On installation, the rotor is secured to the shaft with six #8-32 set screws, square and concentric to the axis of rotation; a bushing adapts it to shafts smaller than 50.8 mm. Sensor wires run along the outside of the shaft and through slots in the rotor to the solder terminals, in stranded wire of 24 AWG at most, then are secured to the shaft and coated with RTV silicone. The stator is held by a flexible restraint, such as a small cable, a spring or a wire tie, rather than by its cable. The silver contacts are wear parts: they are inspected periodically and last about 100 million revolutions under ideal conditions. Each assembly is supplied with a 4.6 m (15 ft) cable and a single mating connector, for the Bendix JT02RE-10-35P connector on the stator.

It is used on automotive drive shafts and half shafts, where torque and shaft speed are recorded on the same assembly.

Six-circuit tubular slip ring with speed encoder

The B6-2/E60 is the six-circuit B-Series tubular slip ring with a built-in speed encoder. It mounts on the shaft, which passes through its 50.8 mm (2 in) bore, and carries strain gages, thermocouples, accelerometers and low voltages through six circuits rated at 1 A. The encoder is a Hall-effect sensor that delivers a 60 pulse-per-revolution, TTL-compatible 5 V square wave, so speed is measured down to 0 rpm; it is powered from 5.5 to 45 V DC. It is 33 mm long and runs up to 7 000 rpm, from −40 to 121 °C.

On installation, the rotor is secured to the shaft with six #8-32 set screws, square and concentric to the axis of rotation; a bushing adapts it to shafts smaller than 50.8 mm. Sensor wires run along the outside of the shaft and through slots in the rotor to the solder terminals, in stranded wire of 24 AWG at most, then are secured to the shaft and coated with RTV silicone. The stator is held by a flexible restraint, such as a small cable, a spring or a wire tie, rather than by its cable. The silver contacts are wear parts: they are inspected periodically and last about 100 million revolutions under ideal conditions. Each assembly is supplied with a 4.6 m (15 ft) cable and a single mating connector, for the Bendix JT02RE-10-35P connector on the stator.

It is used on automotive drive shafts, for example to record torque, axial force and shaft speed on the same prop shaft or half shaft.

Eight-circuit tubular slip ring with speed encoder

The B8-2/E60 is the eight-circuit B-Series tubular slip ring with a built-in speed encoder. It mounts on the shaft, which passes through its 50.8 mm (2 in) bore, and carries strain gages, thermocouples, accelerometers and low voltages through eight circuits rated at 1 A. The encoder is a Hall-effect sensor that delivers a 60 pulse-per-revolution, TTL-compatible 5 V square wave, so speed is measured down to 0 rpm; it is powered from 5.5 to 45 V DC. It is 33 mm long and runs up to 7 000 rpm, from −40 to 121 °C.

On installation, the rotor is secured to the shaft with six #8-32 set screws, square and concentric to the axis of rotation; a bushing adapts it to shafts smaller than 50.8 mm. Sensor wires run along the outside of the shaft and through slots in the rotor to the solder terminals, in stranded wire of 24 AWG at most, then are secured to the shaft and coated with RTV silicone. The stator is held by a flexible restraint, such as a small cable, a spring or a wire tie, rather than by its cable. The silver contacts are wear parts: they are inspected periodically and last about 100 million revolutions under ideal conditions. Each assembly is supplied with a 4.6 m (15 ft) cable and a single mating connector, for the Bendix JT02RE-10-35P connector on the stator.

It is used on automotive drive shafts, for example to measure torque and thrust on the same shaft, or up to five strain gage or thermocouple signals amplified on the rotating side, together with shaft speed.

Weatherproof four-circuit tubular slip ring

The B4-2W is a weatherproof tubular slip ring with four circuits rated at 1 A. It mounts on the shaft, which passes through its 50.8 mm (2 in) bore, and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator; specially designed seals protect it from water, mud, snow, dust and other contaminants. Its rings are solid silver alloy and its brushes silver-graphite. The rotor carries color-coded solder terminals and the stator a Bendix PT02E-8-4P connector. Its stator is 105.7 mm in diameter, it is 32.5 mm long and weighs 1.25 kg, with a contact resistance variation of 0.1 Ω peak; it runs up to 7 000 rpm, from −40 to 121 °C.

On installation, the rotor is secured to the shaft with six #8-32 set screws, square and concentric to the axis of rotation; a bushing adapts it to shafts smaller than 50.8 mm. Sensor wires run along the outside of the shaft and through slots in the rotor to the solder terminals, in stranded wire of 24 AWG at most, then are secured to the shaft and coated with RTV silicone. The stator is held by a flexible restraint, such as a small cable, a spring or a wire tie, rather than by its cable. The silver contacts are wear parts: they are inspected periodically and last about 100 million revolutions under ideal conditions.

It is used on automotive drive shafts in road testing, in rain, mud or snow, for example to measure prop shaft or half shaft torque.

Weatherproof six-circuit tubular slip ring

The B6-2W is a weatherproof tubular slip ring with six circuits rated at 1 A. It mounts on the shaft, which passes through its 50.8 mm (2 in) bore, and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator; specially designed seals protect it from water, mud, snow, dust and other contaminants. Its rings are solid silver alloy and its brushes silver-graphite. The rotor carries color-coded solder terminals and the stator a connector. Its stator is 105.7 mm in diameter and it is 32.5 mm long; it runs up to 7 000 rpm, from −40 to 121 °C.

On installation, the rotor is secured to the shaft with six #8-32 set screws, square and concentric to the axis of rotation; a bushing adapts it to shafts smaller than 50.8 mm. Sensor wires run along the outside of the shaft and through slots in the rotor to the solder terminals, in stranded wire of 24 AWG at most, then are secured to the shaft and coated with RTV silicone. The stator is held by a flexible restraint, such as a small cable, a spring or a wire tie, rather than by its cable. The silver contacts are wear parts: they are inspected periodically and last about 100 million revolutions under ideal conditions.

It is used on automotive drive shafts in road testing, in rain, mud or snow, for example to measure torque and axial force on the same prop shaft.

Thin weatherproof tubular slip ring

The B4-2WT is a thin weatherproof tubular slip ring, 20 mm wide, with four circuits rated at 1 A. It mounts on the shaft, which passes through its 50.8 mm (2 in) bore, and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator; non-contact labyrinth seals protect it from water, mud, snow, dust and other contaminants. Its rings are solid silver alloy and its brushes silver-graphite. The rotor carries solder terminals and the stator a connector, which a lower-profile terminal plate can replace. Its stator is 93.7 mm in diameter and it weighs 1.16 kg, with a contact resistance variation of 0.1 Ω peak; it runs up to 7 000 rpm.

On installation, the rotor is secured to the shaft with six #8-32 set screws, square and concentric to the axis of rotation; a bushing adapts it to shafts smaller than 50.8 mm. Sensor wires run along the outside of the shaft and through slots in the rotor to the solder terminals, in stranded wire of 24 AWG at most, then are secured to the shaft and coated with RTV silicone. The stator is held by a flexible restraint, such as a small cable, a spring or a wire tie, rather than by its cable. The silver contacts are wear parts: they are inspected periodically and last about 100 million revolutions under ideal conditions.

It is used on automotive drive shafts in road testing, where little length is available on the shaft.

Four-circuit tubular slip ring, 3.2 in bore

The B4-3.2 is an open tubular slip ring with four circuits rated at 1 A. It mounts on the shaft, which passes through its 81.3 mm (3.2 in) bore, and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator. Its rings are solid silver alloy and its brushes silver-graphite. The rotor carries solder terminals and the stator a connector. It is 26.9 mm wide and runs up to 4 500 rpm, from −40 to 121 °C.

On installation, the rotor is secured to the shaft with set screws, square and concentric to the axis of rotation; a bushing adapts it to shafts smaller than 81.3 mm. Sensor wires run along the outside of the shaft and through slots in the rotor to the solder terminals, in stranded wire of 24 AWG at most, then are secured to the shaft and coated with RTV silicone. The stator is held by a flexible restraint, such as a small cable, a spring or a wire tie, rather than by its cable. The silver contacts are wear parts: they are inspected periodically and last about 100 million revolutions under ideal conditions.

It is used on large shafts on test rigs and dynamometers.

Six-circuit tubular slip ring, 3.2 in bore

The B6-3.2 is an open tubular slip ring with six circuits rated at 1 A. It mounts on the shaft, which passes through its 81.3 mm (3.2 in) bore, and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator. Its rings are solid silver alloy and its brushes silver-graphite. The rotor carries solder terminals and the stator a connector. It is 26.9 mm wide and runs up to 4 500 rpm, from −40 to 121 °C.

On installation, the rotor is secured to the shaft with set screws, square and concentric to the axis of rotation; a bushing adapts it to shafts smaller than 81.3 mm. Sensor wires run along the outside of the shaft and through slots in the rotor to the solder terminals, in stranded wire of 24 AWG at most, then are secured to the shaft and coated with RTV silicone. The stator is held by a flexible restraint, such as a small cable, a spring or a wire tie, rather than by its cable. The silver contacts are wear parts: they are inspected periodically and last about 100 million revolutions under ideal conditions.

It is used on large shafts on test rigs and dynamometers, when more circuits are needed than on the B4-3.2.

Weatherproof six-circuit tubular slip ring, 3.2 in bore

The B6-3.2W is a weatherproof tubular slip ring with six circuits rated at 1 A. It mounts on the shaft, which passes through its 81.3 mm (3.2 in) bore, and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator; specially designed seals protect it from water, mud, snow, dust and other contaminants. Its rings are solid silver alloy and its brushes silver-graphite. The rotor carries color-coded solder terminals and the stator a connector. Its stator is 93.7 mm in diameter and it is 41.2 mm long; it runs up to 4 500 rpm, from −40 to 121 °C.

On installation, the rotor is secured to the shaft with set screws, square and concentric to the axis of rotation; a bushing adapts it to shafts smaller than 81.3 mm. Sensor wires run along the outside of the shaft and through slots in the rotor to the solder terminals, in stranded wire of 24 AWG at most, then are secured to the shaft and coated with RTV silicone. The stator is held by a flexible restraint, such as a small cable, a spring or a wire tie, rather than by its cable. The silver contacts are wear parts: they are inspected periodically and last about 100 million revolutions under ideal conditions.

It is used on large automotive drive shafts in road testing, for example to measure torque and axial force on the same shaft, or with strain gage amplifiers on the rotating side.

Weatherproof tubular slip ring with speed encoder, 3.2 in bore

The B6-3.2W/E60 is the B6-3.2W weatherproof tubular slip ring with a 60 pulse-per-revolution encoder for shaft speed. It mounts on the shaft, which passes through its 81.3 mm (3.2 in) bore, and carries strain gages, thermocouples, accelerometers and low voltages through six circuits rated at 1 A; specially designed seals protect it from water, mud, snow, dust and other contaminants. Its rings are solid silver alloy and its brushes silver-graphite. Its stator is 93.7 mm in diameter and it is 41.2 mm long; it runs up to 4 500 rpm, from −40 to 121 °C.

On installation, the rotor is secured to the shaft with set screws, square and concentric to the axis of rotation; a bushing adapts it to shafts smaller than 81.3 mm. Sensor wires run along the outside of the shaft and through slots in the rotor to the solder terminals, in stranded wire of 24 AWG at most, then are secured to the shaft and coated with RTV silicone. The stator is held by a flexible restraint, such as a small cable, a spring or a wire tie, rather than by its cable. The silver contacts are wear parts: they are inspected periodically and last about 100 million revolutions under ideal conditions.

It is used on large automotive drive shafts in road testing, where torque and shaft speed are recorded on the same assembly.

Weatherproof tubular slip ring for 31.5 mm half shafts

The B7-T-1.24W is a weatherproof tubular slip ring with seven circuits rated at 1 A. It mounts on a 31.5 mm half shaft, which passes through its bore, and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator. Its rings are solid silver alloy and its brushes silver-graphite. Its stator is 71.8 mm in diameter and it is 71.7 mm long; it runs up to 3 500 rpm, from −40 to 121 °C.

On installation, the rotor is secured to the half shaft square and concentric to the axis of rotation. Sensor wires run along the shaft to the rotor terminals and are secured to it, and the stator is held by a flexible restraint rather than by its cable. The silver contacts are wear parts and are inspected periodically.

It is used for long-term half shaft torque measurement in all weather.

Weatherproof tubular slip ring for 30 mm half shafts

The B7-T-1.2W is a weatherproof tubular slip ring with seven circuits rated at 1 A. It mounts on a 30 mm half shaft, which passes through its bore, and carries strain gages, thermocouples, accelerometers and low voltages from rotor to stator. Its rings are solid silver alloy and its brushes silver-graphite. Its stator is 71.8 mm in diameter and it is 71.7 mm long; it runs up to 3 500 rpm, from −40 to 121 °C.

On installation, the rotor is secured to the half shaft square and concentric to the axis of rotation. Sensor wires run along the shaft to the rotor terminals and are secured to it, and the stator is held by a flexible restraint rather than by its cable. The silver contacts are wear parts and are inspected periodically.

It is used for long-term half shaft torque measurement in all weather.

Circuits	4
Rotation sensor	None
Current per circuit	1 A
Mounting	Through bore
Max speed	7 000 rpm
Shaft diameter	50.8 mm
Dimensions	length 26.92 mm
Connections	Solder terminals · Connector (rotor: solder terminals · stator: connector)

Circuits	6
Rotation sensor	None
Current per circuit	1 A
Mounting	Through bore
Max speed	7 000 rpm
Shaft diameter	50.8 mm
Dimensions	length 26.92 mm
Connections	Solder terminals · Connector (rotor: solder terminals · stator: connector)

Circuits	8
Rotation sensor	None
Current per circuit	1 A
Mounting	Through bore
Max speed	7 000 rpm
Shaft diameter	50.8 mm
Dimensions	length 26.92 mm
Connections	Solder terminals · Connector (rotor: solder terminals · stator: connector)

Circuits	4
Rotation sensor	Encoder
Encoder resolution	60 ppr
Current per circuit	1 A
Mounting	Through bore
Max speed	7 000 rpm
Shaft diameter	50.8 mm
Dimensions	length 33 mm
Operating temperature	−40 to 121 °C
Connections	Solder terminals · Connector (rotor: solder terminals · stator: connector)

Circuits	6
Rotation sensor	Encoder
Encoder resolution	60 ppr
Current per circuit	1 A
Mounting	Through bore
Max speed	7 000 rpm
Shaft diameter	50.8 mm
Dimensions	length 33 mm
Operating temperature	−40 to 121 °C
Connections	Solder terminals · Connector (rotor: solder terminals · stator: connector)

B7-T-1.2W tubular slip ring B-Series

Four-circuit tubular slip ring, 2 in bore

Six-circuit tubular slip ring, 2 in bore

Eight-circuit tubular slip ring, 2 in bore

Four-circuit tubular slip ring with speed encoder

Six-circuit tubular slip ring with speed encoder

Eight-circuit tubular slip ring with speed encoder

Weatherproof four-circuit tubular slip ring

Weatherproof six-circuit tubular slip ring

Thin weatherproof tubular slip ring

Four-circuit tubular slip ring, 3.2 in bore

Six-circuit tubular slip ring, 3.2 in bore

Weatherproof six-circuit tubular slip ring, 3.2 in bore

Weatherproof tubular slip ring with speed encoder, 3.2 in bore

Weatherproof tubular slip ring for 31.5 mm half shafts

Weatherproof tubular slip ring for 30 mm half shafts

Specifications

Request a quote

Resources

Datasheets and manuals

Drawings

CAD models

Datasheets and manuals

Drawings

CAD models

Datasheets and manuals

Drawings

CAD models

Datasheets and manuals

Drawings

CAD models

Datasheets and manuals

Drawings

CAD models

Datasheets and manuals

Drawings

CAD models

Datasheets and manuals

Drawings

CAD models

Datasheets and manuals

Drawings

CAD models

Datasheets and manuals

Drawings

CAD models

Datasheets and manuals

Drawings

CAD models

Datasheets and manuals

Drawings

CAD models

Datasheets and manuals

Drawings

CAD models

Datasheets and manuals

Drawings

CAD models

Datasheets and manuals

Drawings

CAD models

Datasheets and manuals

Drawings

CAD models

Related applications

If the B-Series is not the one

A question on this product?